Banner

Oscillating Tube of IEC60529 IPX3 Waterproof Test Setup

For checking the protection against water with spray nozzle of 0,4 mm bore are used to prove the degrees of protection for the second characteristic numerals 3 and 4 “Protection against Spraying Water” resp. “Protection against splashing Water”.

  • Item NO.:

    ZLT-DP
  • Order(MOQ):

    1
  • Payment:

    T/T
  • Product Origin:

    China
  • Shipping Port:

    Guangzhou
  • Lead Time:

    25 days
  • Product Detail

Oscillating Tubes Device

Oscillating Tube of IEC60529 IPX3 Waterproof Test Setup

Product details: Model ZLT-DP

For checking the protection against water with spray nozzle of 0,4 mm bore are used to prove the degrees of protection for the second characteristic numerals 3 and 4 “Protection against Spraying Water” resp. “Protection against splashing Water”.
The protection against spraying water is determined by causing the oscillating tube to oscillate over the specimen through an angle of 60°on either side of the vertical each at a speed of about 60°per second, while the jets coming from a larger angle than 60°to the vertical are baffled by deflectors. But there is also a slightly amended regulation, according to which the oscillating tube with deflectors stands still in a vertical position, and the specimen is turned-for example on a turntable-at a convenient speed a vertical axis.
In order to determine the protection against splashing water, the oscillating tube is caused to oscillate through an angle of almost 180°on either side of the vertical at a speed of about 60°per second, while depending on regulation the specimen stands still or is turned at a convenient speed. Each of these tests lasts for example 10 minutes.
A complete test unit comprises a set of oscillating tubes as accessories, the oscillating appliance with the drive and-in the case of larger oscillating tubes-the opposite bearing. The oscillating tubes are manufactured with orifice radii of 200 mm to 1600 mm with a progressive ratio of 200 mm.
According to IEC60529 figure 4, IEC60598 clause 9.2.5, IEC60947.
Standard Outfit:
1 oscillating appliance, with flanged shaft to screw on the oscillating tubes, height above floor 1400 mm, on request with a second flanged shaft as shown on figure,

    1 drive by 750W servo motor, oscillating speed 60°/s, with frequency converter, swiveling angle sensor, swiveling angle limiting safety switch, electromagnetic brake, brake release switch, emergency stopping switch and watertight socket to connect a turntable,


   1 water supply with fine filter to be cleaned by reverse flow, pressure regulator and pressure indicating instruments, adjustable flow regulating valve and flow indicating instrument, electromagnetic valve and rotary union to supply the water through the flanged shaft, prepared to connect a hose of nominal diameter 20 mm,


     1 resp. 2 opposite bearings, with flanged shaft to screw on the oscillating tubes, wall fastening type, also available for floor fastening,

    1 control system, with start and stop buttons, switches for water, oscillating drive and turntable drive, main switch and emergency stopping switch to be unlocked by key, rotary knob to adjust the swiveling angle infinitely from 60°to minimum 165°on either side of the vertical, feasibility to adjust the oscillating angle mid position, fuses and thermal excess current release.

oscillating tubes





















Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Related Products
IEC60529 IP1
Sphere 50 mm diameter of IEC60529 IP1 test probe A
IP1 Code of IEC60529 IP1X. Also used to verify protection from access with the back of the hand for an IP suffix A code. conform to IEC61032 test probe A and IEC60529 IP1 and other standard.With dynamometer 50N±5N, 50 mm diameter.
IEC60529 IP3 Test Probe
Rigid Steel Rod 2.5mm Diameter 100mm Long of IEC60529 IP3 Test Probe C
IP3 Code of IEC60529 IP3X. Meets IEC61032 test probe C and EN Standards, including IEC 60529 for IP3 and suffix C codes. With dynamometer 3N±0.3N,
expanded metal spacer
Expanded Metal Spacer of IEC60598 Spacer Test Apparatus
Expanded Metal Spacer,according to IEC60598 clause 9.2.
IEC60529 IP2 jointed test finger
Jointed Test Finger of IEC60529 IP2 Test Probe B
IP2 Code of IEC60529 IP2X. Conform to IEC61032 test probe B, IEC60950 figure 2A, IEC60529IP2, UL1278 figure 8.4 etc .With dynamometer 10N±1N,
IEC60529 IP3 Test Probe
Rigid Steel Rod 1.0mm Diameter 100mm Long of IEC60529 IP4 Test Probe D
IP4 Code of IEC60529 IP4X. Meets IEC61032 test probe D  and EN Standards, including IEC 60529 for IP4 and suffix D codes. With dynamometer 3N±0.3N,
IEC60529 IP2 Test Sphere
Rigid Test Sphere 12.5mm Diameter of IEC60529 IP2
IP2 Code and IP2X. conforms to IEC60529 IP2 and IEC61032 test probe 2. With dynamometer 30N±0,3N
Dustproof Test Chamber Machine
Dust Test Chamber of IEC60529 IP5 Testing Equipment
IP5 Code and IP5X. In accordance with IEC60529/2001 figure 2 and IEC 60598 etc.
Spray Nozzle
Spray Nozzle of IEC60529 IPX4 Hand Held Device Test Equipment
to prove the degrees of protection with the second characteristic numerals 3 “Protected against Spraying Water” and 4 “Protected against Splashing Water”, in accordance with IEC60529 figure 5, IEC60335 clause 15.1.1, IEC60598.

click here to leave a message

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

about

contact